View LTC106309_4540146.PDF datasheet online --- IC-ON-LINE

Datasheet File OCR Text:

LTC1063 DC Accurate, Clock-Tunable 5th Order Butterworth Lowpass Filter
FEATURES

DESCRIPTIO
Clock-Tunable Cutoff Frequency 1mV DC Offset (Typical) 80dB CMRR (Typical) Internal or External Clock 50VRMS Clock Feedthrough 100:1 Clock-to-Cutoff Frequency Ratio 95VRMS Total Wideband Noise 0.01% THD at 2VRMS Output Level 50kHz Maximum Cutoff Frequency Cascadable for Faster Roll-Off Operates from 2.375 to 8V Power Supplies Self-Clocking with 1 RC Available in 8-Pin DIP and 16-Pin SO Wide Packages
The LTC(R)1063 is the first monolithic filter providing both clock-tunability, low DC output offset and over 12-bit DC accuracy. The frequency response of the LTC1063 closely approximates a 5th order Butterworth polynomial. With appropriate PCB layout techniques the output DC offset is typically 1mV and is constant over a wide range of clock frequencies. With 5V supplies and 4V input voltage range, the CMR of the device is 80dB. The filter cutoff frequency is controlled either by an internal or external clock. The clock-to-cutoff frequency ratio is 100:1. The on-board clock is power supply independent, and it is programmed via an external RC. The 50VRMS clock feedthrough is considerably reduced over existing monolithic filters. The LTC1063 wideband noise is 95VRMS, and it can process large AC input signals with low distortion. With 7.5V supplies, for instance, the filter handles up to 4VRMS (92dB S/N ratio) while the standard 1kHz THD is below 0.02%; 80dB dynamic ranges (S/N +THD) is obtained with input levels between 1VRMS and 2.3VRMS. The LTC1063 is available in 8-pin miniDIP and 16-pin SO wide packages. For a linear phase response, see LTC1065 data sheet.
APPLICATIO S

Audio Strain Gauge Amplifiers Anti-Aliasing Filters Low Level Filtering Digital Voltmeters 60Hz Lowpass Filters Smoothing Filters Reconstruction Filters
, LTC and LT are registered trademarks of Linear Technology Corporation. All other trademarks are the property of their respective owners.
TYPICAL APPLICATIO
VIN** 1 2 3 -5V 4 LTC1063
2.5kHz 5th Order Lowpass Filter
8 7 6 5 VOUT 5V 0.1F
10 0 -10 -20
GAIN (dB)
-30 -40 -50 -60 -70
0.1F
*19.1k
200pF*
* SELF-CLOCKING SCHEME ** IF THE INPUT VOLTAGE CAN EXCEED V +,
-80 -90
1063 TA01
CONNECT A SIGNAL DIODE BETWEEN PIN 1 AND V +.
1
U
Frequency Response
10 FREQUENCY (kHz) 100
1063 TA02
U
U
1063fa
1
LTC1063
ABSOLUTE MAXIMUM RATINGS (Note 1)
Total Supply Voltage (V + to V -) .......................... 16.5V Power Dissipation ............................................. 400mW Voltage at Any Input .... (V - - 0.3V) VIN (V + + 0.3V) Burn-In Voltage ...................................................... 16V Operating Temperature Range ............... - 40C to 85C Storage Temperature Range ................ - 65C to 150C Lead Temperature (Soldering, 10 sec)................. 300C
PACKAGE/ORDER I FOR ATIO
TOP VIEW VIN 1 GND 2 V- 3 CLK OUT 4 8 7 6 5 VOS ADJ VOUT V+ CLK IN
ORDER PART NUMBER LTC1063CN8
N8 PACKAGE 8-LEAD PLASTIC DIP TJMAX = 100C, JA = 110C/W (N)
J8 PACKAGE 8-LEAD CERAMIC DIP TJMAX = 150C, JA = 100C/W (J)
LTC1063CJ8 LTC1063MJ8
OBSOLETE PACKAGE
Consider the N8 Package for Alternate Source
Order Options Tape and Reel: Add #TR Lead Free: Add #PBF Lead Free Tape and Reel: Add #TRPBF Lead Free Part Marking: http://www.linear.com/leadfree/ Consult LTC Marketing for parts specified with wider operating temperature ranges.
The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at VS = 5V, fCLK = 500kHz, fC = 5kHz, RL = 10k, TA = 25C, unless otherwise specified.
PARAMETER Clock-to-Cutoff Frequency Ratio (fCLK / fC) Maximum Clock Frequency (Note 2) CONDITIONS 2.375V VS 7.5V VS = 7.5V VS = 5V VS = 2.5V 2.5V VS 7.5V, TA < 85C 0 VS = 5V, fCLK = 25kHz, fC = 250Hz fIN = 250Hz VS = 5V, fCLK = 500kHz, fC = 5kHz fIN = 100Hz fIN = 1kHz = 0.2fC fIN = 2.5kHz = 0.5fC fIN = 4kHz = 0.8fC

ELECTRICAL CHARACTERISTICS
Minimum Clock Frequency (Note 3) Input Frequency Range Filter Gain
2
U
U
W
WW
U
W
TOP VIEW NC 1 VIN 2 GND 3 NC 4 V- 5 16 VOS ADJ 15 NC 14 VOUT 13 NC 12 V + 11 NC 10 NC 9 CLK IN
ORDER PART NUMBER LTC1063CSW
NC 6 NC 7 CLK OUT 8
SW PACKAGE 16-LEAD PLASTIC SO WIDE TJMAX = 100C, JA = 85C/W
MIN
TYP 100 0.5 5 4 3 30
MAX
UNITS MHz MHz MHz Hz
0.9fCLK - 3.0 - 3.0 0 - 2.5 - 2.4 dB dB dB 0.04 0.055 0.41 0.46 0.1 0.2 dB dB dB dB dB dB
1063fa
- 3.5 - 3.6
- 0.06 - 0.075 - 0.09 - 0.14 - 0.5 - 0.6
- 0.01 - 0.01 0.16 0.16 - 0.2 - 0.2
LTC1063
The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at VS = 5V, fCLK = 500kHz, fC = 5kHz, RL = 10k, TA = 25C, unless otherwise specified.
PARAMETER CONDITIONS fIN = 5kHz = fC fIN = 20kHz = 4fC

ELECTRICAL CHARACTERISTICS
MIN - 3.5 - 3.6 - 57.5 - 57.0 - 0.066 - 0.081 - 0.24 - 0.29 - 0.6 - 0.7 - 3.5 - 3.6
TYP - 3.0 - 3.0 - 60.0 - 60.0 0.004 0.004 0.16 0.16 - 0.2 - 0.2 - 3.0 - 3.0 50 100 -80
MAX - 2.5 - 2.4 - 62.0 - 62.5 0.074 0.089 0.56 0.61 0.2 0.3 - 2.5 - 2.4
UNITS dB dB dB dB dB dB dB dB dB dB dB dB VRMS VRMS dB V V V V V V nA M mV mV mV V/C V/C V/C
Filter Gain
VS = 2.375V, fCLK = 500kHz, fC = 5kHz fIN = 1kHz
fIN = 2.5kHz
fIN = 4kHz
fIN = 5kHz
Clock Feedthrough Wideband Noise (Note 4) THD + Wideband Noise (Note 5) Filter Output DC Swing
2.375 VS 7.5V 2.375 VS 7.5V, 1Hz < f < fCLK VS = 7.5V, fC = 20kHz, fIN = 1kHz, 1VRMS VIN 2.3VRMS VS = 2.375V
1.6/- 2.0 1.4/- 1.8 4.0/- 4.5 3.8/- 4.3 6.5/- 7.0 6.3/- 6.8
1.7/- 2.2 4.3/- 4.8 6.8/- 7.3 10 800
VS = 5V
VS = 7.5V
Input Bias Current Dynamic Input Impedance Output DC Offset (Note 6) VS = 2.375V VS = 5V VS = 7.5V VS = 2.375V VS = 5V VS = 7.5V R (Pin 4 to 5) = 20k, C (Pin 5 to GND) = 470pF VS = 2.375V
2 0 -4 10 20 25 99 95 102 98 104 101 105 103 108 106 110 109 1.43 0.47 3 1 4.5 1.5
5
Output DC Offset Drift
Self-Clocking Frequency (fOSC)
112 114 114 114 116 116
kHz kHz kHz kHz kHz kHz V V V V V V
VS = 5V
VS = 7.5V
External CLK Pin Logic Thresholds
VS = 2.375V VS = 5V VS = 7.5V
Min Logical "1" Max Logical "0" Min Logical "1" Max Logical "0" Min Logical "1" Max Logical "0"
1063fa
3
LTC1063
ELECTRICAL CHARACTERISTICS
PARAMETER Power Supply Current CONDITIONS VS = 2.375V, fCLK = 500kHz
The denotes the specifications which apply over the full operating temperature range, otherwise specifications are at VS = 5V, fCLK = 500kHz, fC = 5kHz, RL = 10k, TA = 25C, unless otherwise specified.
MIN TYP 2.7 5.5
MAX 4.0 5.5 8 11 11 14.5
UNITS mA mA mA mA mA mA
VS = 5V, fCLK = 500kHz VS = 7.5V, fCLK = 500kHz
7.0
Note 1: Absolute Maximum Ratings are those values beyond which the life of a device may be impaired. Note 2: The maximum clock frequency criterion is arbitrarily defined as: The frequency at which the filter AC response exhibits 1dB of gain peaking. Note 3: At limited temperature ranges (i.e., TA 50C) the minimum clock frequency can be as low as 10Hz. The minimum clock frequency is arbitrarily defined as: the clock frequency at which the output DC offset changes by more than 1mV.
Note 4: The wideband noise specification does not include the clock feedthrough. Note 5: To properly evaluate the filter's harmonic distortion an inverting output buffer is recommended as shown in the Test Circuit. An output buffer is not necessarily needed when measuring output DC offset or wideband noise. Note 6: The output DC offset is optimized for 5V supply. The output DC offset shifts when the power supplies change; however this phenomenon is repeatable and predictable.
TYPICAL PERFOR A CE CHARACTERISTICS
Self-Clocking Frequency vs R
110 100
LTC1063
90
4 R C = 200pF fOSC 1/RC
R PINS 4 TO 5 (k)
80 70 60 50 40 30 20 10 100 300 FREQUENCY (kHz) 500
1063 G01
OUTPUT OFFSET (mV)
OUTPUT OFFSET (mV)
4
UW
5 C
Output Offset vs Clock, Low Clock Rates
50 45 40 35 30 25 20 15 10 5 0 10 B A 110 EXTERNAL CLOCK FREQUENCY (Hz) 210 VS = 5V A: TA = 25C B: TA = 85C 5 4 3 2 1 0 -1 -2 -3 -4 -5
Output Offset vs Clock, Medium Clock Rates
VS = 7.5V
VS = 5V
VS = 2.5V
0
500 1000 EXTERNAL CLOCK FREQUENCY (kHz)
1063 G03
1063 G02
1063fa
LTC1063 TYPICAL PERFOR A CE CHARACTERISTICS
Gain vs Frequency; VS = 2.5V
10 0 -10 -20
GAIN (dB)
-40 -50 -60 -70 -80 -90 1 VIN = 750mVRMS TA = 25C A. fCLK = 0.5MHz B. fCLK = 1MHz C. fCLK = 2MHz
A
GAIN (dB)
B
C
-40 -50 -60 -70 -80 -90 VIN = 1.5VRMS TA = 25C 1 A. fCLK = 1MHz B. fCLK = 2MHz C. fCLK = 3MHz D. fCLK = 4MHz
A
BC
GAIN (dB)
-30
10 INPUT FREQUENCY (kHz)
THD + Noise vs Input Voltage; VS = Single 5V
1 fIN = 1kHz, TA = 25C 5 REPRESENTATIVE UNITS
1
THD + NOISE (%)
THD + NOISE (%)
0.1
THD (%)
B A 0.01
A. fC = 5kHz, fCLK = 0.5MHz B. fC = 10kHz, fCLK = 1MHz 0.001 0.1
0.001
1 INPUT (VRMS)
THD vs Frequency; VS = 5V
1 VIN = 1.5VRMS fC = 10kHz, fCLK = 1MHz S/N = 83.5dB, TA = 25C 5 REPRESENTATIVE UNITS 0.1 THD + NOISE (%)
THD (%)
B 0.01 A
0.01
THD (%)
0.001 1 5 FREQUENCY (kHz) 10
1063 G10
UW
100 200
1063 G04
Gain vs Frequency; VS = 5V
10 0 -10 -20 -30 D
10 0 -10 -20 -30 -40 -50 -60 -70 -80 -90
Gain vs Frequency; VS = 7.5V
D A BC E
A. fCLK = 1MHz B. fCLK = 2MHz C. fCLK = 3MHz D. fCLK = 4MHz E. fCLK = 5MHz
VIN = 2.5VRMS TA = 25C
1 10 INPUT FREQUENCY (kHz) 100 200
1063 G06
10 INPUT FREQUENCY (kHz)
100 200
1063 G05
THD vs Frequency; VS = Single 5V
1
VIN = 0.75VRMS fC = 5kHz, fCLK = 500kHz S/N = 78dB, TA = 25C 5 REPRESENTATIVE UNITS 0.1
THD + Noise vs Input Voltage; VS = 5V
fIN = 1kHz, TA = 25C 5 REPRESENTATIVE UNITS
0.1 B A 0.01
0.01
A. fC = 10kHz, fCLK = 1MHz B. fC = 20kHz, fCLK = 2MHz 5
1063 G07
1
2 3 FREQUENCY (kHz)
4
5
1063 G08
0.001 0.1
1 INPUT (VRMS)
5
1063 G09
THD + Noise vs Input Voltage; VS = 7.5V
1 fIN = 1kHz, TA = 25C 5 REPRESENTATIVE UNITS
1
THD vs Frequency; VS = 7.5V
VIN = 2.5VRMS fC = 10kHz, fCLK = 1MHz S/N = 88dB, TA = 25C 5 REPRESENTATIVE UNITS 0.1
0.1
0.01
A. fC = 10kHz, fCLK = 1MHz B. fC = 20kHz, fCLK = 2MHz 0.001 0.1
0.001
1 INPUT (VRMS)
5
1063 G11
1
5 FREQUENCY (kHz)
10
1063 G12
1063fa
5
LTC1063 TYPICAL PERFOR A CE CHARACTERISTICS
Passband Gain and Phase vs Input Frequency
1 0
PASSBAND GAIN (dB)
2.5V VS 7.5V, TA = 25C
PHASE MISMATCH (DEG)
-1 -2 -3 -4 -5 fCLK =100kHz fC =1kHz fCLK =1MHz fC =10kHz A PHASE A B PHASE B
-6 100
1k 10k INPUT FREQUENCY (Hz)
Power Supply Current vs Power Supply Voltage
10 9 -40C
POWER SUPPLY CURRENT (mA)
8 7 6 5 4 3 2 1 0 0 2 4 6 8 10 12 14 16 18 20 TOTAL POWER SUPPLY VOLTAGE (V)
1063 G15
6
UW
Phase Matching
0 -20 -60
PHASE (DEG)
1.2 1.1 1.0 0.9 0.8 0.7 0.6 0.5 0.4 0.3 0.2 0.1 0 02 4 6 8 10 12 14 16 18 20 22 24 INPUT FREQUENCY (kHz)
1063 G14
VS = 7.5V VIN = 1VRMS fCLK = 2MHz fC = 20kHz
-100 -140 -180 -220
-260 100k
1063 G13
Transient Response
25C 85C
HORIZONTAL: 0.1ms/DIV, VERTICAL: 2V/DIV VS = 5V, fC = 10kHz, VIN = 1kHz 3VP SQUARE WAVE
1063 G16
1063fa
LTC1063 PI FU CTIO S
Power Supply Pins (Pins 6, 3, N Package) The positive and negative supply pin should be bypassed with a high quality 0.1F ceramic capacitor. In applications where the clock pin (5) is externally swept to provide several cutoff frequencies, the output DC offset variation is minimized by connecting an additional 1F solid tantalum capacitor in parallel with the 0.1F disc ceramic. This technique was used to generate the graphs of the output DC offset variation versus clock; they are illustrated in the Typical Performance Characteristics section. When the power supply voltage exceeds 7V, and when V - is applied before V +, if V+ is allowed to go below ground, connect a signal diode between the positive supply pin and ground to prevent latch-up (see Typical Applications). Ground Pin (Pin 2, N Package) The ground pin merges the internal analog and digital ground paths. The potential of the ground pin is the reference for the internal switched-capacitor resistors, and the reference for the external clock. The positive input of the internal op amp is also tied to the ground pin. For dual supply operation, the ground pin should be connected to a high quality AC and DC ground. A ground plane, if possible, should be used. A poor ground will degrade DC offset and it will increase clock feedthrough, noise and distortion. A small amount of AC current flows out of the ground pin whether or not the internal oscillator is used. The frequency of the ground current equals the frequency of the internal or external clock. The average value of this current is approximately 55A, 110A, 170A for 2.5V, 5V and 7.5V supplies respectively. For single supply operation, the ground pin should be preferably biased at half supply (see Typical Applications). VOS Adjust Pin (Pin 8, N Package) The VOS adjust pin can be used to trim any small amount of output DC offset voltage or to introduce a desired output DC level. The DC gain from the VOS adjust pin to the filter output pin equals two. Any DC voltage applied to this pin will reflect at the output pin of the filter multiplied by two. If the VOS adjust pin is not used, it should be shorted to the ground pin. The DC bias current flowing into the VOS adjust pin is typically 10pA. Pin 8 should always be connected to an AC ground; AC signals applied to this pin will degrade the filter response. Input Pin (Pin 1, N Package) Pin 1 is the filter input and it is connected to an internal switched-capacitor resistor. If the input pin is left floating, the filter output will saturate. The DC input impedance of pin 1 is very high; with 5V supplies and 1MHz clock, the DC input impedance is typically 1G. A resistor, RIN, in series, with the input pin will not alter the value of the filter's DC output offset (Figure 1). RIN should, however, be limited to a maximum value (Table 1), otherwise the filter's passband flatness will be affected. Refer to the Applications Information section for more details.
VIN RIN 1 2 3 V- 4 LTC1063 8 7 6 VOUT V+
U
U
U
5f CLK
1063 F01
Figure 1. Table 1. RIN(MAX) vs Clock and Power Supply
RIN(MAX) VS = 7.5V fCLK = 4MHz fCLK = 3MHz fCLK = 2MHz fCLK = 1MHz fCLK = 500kHz fCLK = 100kHz 2.2k 3.4k 5.5k 11k 24k 120k VS = 5V - 2.9k 5k 11k 23k 120k VS = 2.5V - - 2.7k 9.2k 21k 110k
1063fa
7
LTC1063
PI FU CTIO S
Output Pin (Pin 7, N Package) Pin 7 is the filter output. This pin can typically source over 20mA and sink 2mA. Pin 7 should not drive long coax cables, otherwise the filter's total harmonic distortion will degrade. Clock Input Pin (Pin 5, N Package) An external clock when applied to pin 5 tunes the filter cutoff frequency. The clock-to-cutoff frequency ratio is 100:1. The high (VHIGH) and low (VLOW) clock logic threshold levels are illustrated in Table 2. Square wave clocks with duty cycles between 30% and 50% are strongly recommended. Sinewave clocks are not recommended.
Table 2. Clock Pin Threshold Levels
POWER SUPPLY VS = 2.5V VS = 5V VS = 7.5V VS = 8V VS = 5V, 0V VS = 12, 0V VS =15V, 0V VHIGH 1.5V 3V 4.5V 4.8V 4V 9.6V 12V VLOW 0.5V 1V 1.5V 1.6V 3V 7.2V 9V
MAXIMUM LOAD CAPACITANCE (pF )
TEST CIRCUIT
+
LT1022 VIN 1 2 3 V- 4 0.1F CLOCK IN
1063 TC01
8
U
U
U
Clock Output Pin (Pin 4, N Package) Any external clock applied to the clock input pin appears at the clock output pin. The duty cycle of the clock output equals the duty cycle of the external clock applied to the clock input pin. The clock output pin swings to the power supply rails. When the LTC1063 is used in a self-clocking mode, the clock of the internal oscillator appears at the clock output pin with a 30% duty cycle. The clock output pin can be used to drive other LTC1063s or other ICs. The maximum capacitance, CL(MAX), the clock output pin can drive is illustrated in Figure 2.
200 180 160 140 120 100 80 60 40 20 0 1 3 2 4 5 6 7 8 9 10 CLOCK FREQUENCY (MHz)
1063 F02
VS = 2.5V
TA = 25C
VS = 5V VS = 7.5V
Figure 2. Maximum Load Capacitance at the Clock Output Pin
VOUT
8 7 LTC1063 6 5 50k V+ 0.1F
-
50k
20pF
Figure 3. Test Circuit for THD
1063fa
LTC1063
APPLICATIO S I FOR ATIO
Self-Clocking Operation
fCLK CHANGE NORMALIZED TO ITS 25C VALUE (%)
The LTC1063 features an internal oscillator which can be tuned via an external RC. The LTC1063's internal oscillator is primarily intended for generation of clock frequencies below 500kHz. The first curve of the Typical Performance Characteristics section shows how to quickly choose the value of the RC for a given frequency. More precisely, the frequency of the internal oscillator is equal to: fCLK = K/RC For clock frequencies (fCLK) below 100kHz, K equals 1.07. Figure 4b shows the variation of the parameter K versus clock frequency and power supply. First choose the desired clock frequency, (fCLK < 500kHz), then through Figure 4b pick the right value of K, set C = 200pF and solve for R. Example 1: fCUTOFF = 2kHz, fCLK = 200kHz, VS = 5V, TA = 25C, K = 1.0, C = 200pF then, R = (1.0)/(200kHz x 204pF) = 24.5k.
VIN 1 2 3 V- 4 R LTC1063 8 7 6 5 VOUT V+
C
1063 F04a
Figure 4a.
1.25 1.20 1.15 1.10 1.05 1.00 0.95 0.90 0.85 0.80 0.75 400 100 300 500 200 INTERNAL CLOCK FREQUENCY (kHz)
1063 F04b
FCLK = K/RC C = 200pF TA = 25C
VS = 7.5V
K
VS = 5V
K
VS = 2.5V
Figure 4b. fCLK vs K
U
Note a 4pF parasitic capacitance is assumed in parallel with the external 200pF timing capacitor. Figure 5 shows the clock frequency variation from - 40C to 85C. The 200kHz clock of Example 1 will change by -1.75% at 85C.
4 3 2 1 0 -1 -2 -3 -4 0 100 300 400 200 CLOCK FREQUENCY (kHz) 500
1063 F05
W
UU
C = 200pF VS = 2.5V
TA = -40C VS = 5V VS = 7.5V TA = 85C VS = 7.5V
VS = 2.5V
VS = 5V
Figure 5. fCLK vs Temperature
For a very limited temperature range, the internal oscillator of the LTC1063 can be used to generate clock frequencies above 500kHz (Figures 6 and 7). The data of Figure 6 is derived from several devices. For a given external (RC) value, the observed device-to-device clock frequency variation was 1% (VS = 5V), and 1.25% for VS = 2.5V. Example 2: fCUTOFF = 20kHz, fCLK = 2MHz, VS = 7.5V, TA = 25C, C = 10pF from Figure 6, K = 0.575, and, R = (0.575)/(2MHz x 14pF) = 20.5k.
0.80 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0.5 1.0 2.0 2.5 1.5 CLOCK FREQUENCY (MHz) 3.0
1063 F06
fCLK = K/RC C = 10pF TA = 25C
VS = 7.5V VS = 5V
VS = 2.5V
Figure 6. fCLK vs K
1063fa
9
LTC1063
APPLICATIO S I FOR ATIO
0.80 0.75 0.70 0.65 0.60 0.55 0.50 0.45 0.40 0.5 VS = 2.5V 1.0 2.0 2.5 1.5 CLOCK FREQUENCY (MHz) 3.0
1063 F07
fCLK = K/RC C = 10pF TA = 70C
K
VS = 7.5V VS = 5V
Figure 7. fCLK vs K
A 4pF parasitic capacitance is assumed in parallel with the external 10pF capacitor. A 1% clock frequency variation from device to device can be expected. The 2MHz clock frequency designed above will typically drift to 1.74MHz at 70C (Figure 7). The internal clock of the LTC1063 can be overridden by an external clock provided that the external clock source can drive the timing capacitor, C, which is connected from the clock input pin to ground. Output Offset The DC output offset of the LTC1063 is trimmed to typically less than 1mV . The trimming is done at VS = 5V. To obtain optimum DC offset performance, appropriate PC layout techniques should be used and the filter IC should be soldered to the PC board. A socket will degrade the output DC offset by typically 1mV. The output DC offset is sensitive to the coupling of the clock output pin 4 (N package) to the negative power supply pin 3 (N package). The negative supply pin should be well decoupled. When the surface mount package is used, all the unused pins should be grounded. When the power supplies are fixed, the output DC offset should not change by more than 100V over 10Hz to 1MHz clock frequency variation. When the filter clock frequency is fixed, the output DC offset will typically change by - 4mV (2mV) when the power supply varies from 5V to 7.5V (2.5V). See Typical Performance Characteristics.
10
U
Common Mode Rejection Ratio The common mode rejection ratio is defined as the change of the output DC offset with respect to the DC change of the input voltage applied to the filter. CMRR = 20log (VOS OUT /VIN)(dB) Table 3 illustrates the common mode rejection for three power supplies and three temperatures. The common mode rejection improves if the output offset is adjusted to approximately 0V. The output offset can be adjusted via pin 8 (N package) (see Typical Applications).
Table 3. CMRR Data, fCLK = 100kHz
POWER SUPPLY 2.5V 5V 7.5V VIN 1.8V 4V 6V - 40C 76dB 74dB 70dB 25C 78dB 79dB 72dB 85C 76dB 75dB 74dB 25C (VOS Nulled) 85dB 82dB 76dB The above data is valid for clock frequencies up to 800kHz, 900kHz, 1MHz, for VS = 2.5V, 5V, 7.5V respectively.
W
UU
Clock Feedthrough Clock feedthrough is defined as the RMS value of the clock frequency and its harmonics which are present at the filter's output pin. The clock feedthrough is tested with the filter input grounded and it depends on the quality of the PC board layout and power supply decoupling. Any parasitic switching transients, during the rise and fall of the incoming clock, are not part of the clock feedthrough specifications; their amplitude strongly depends on scope probing techniques as well as ground quality and power supply bypassing. For a power supply VS = 5V, the clock feedthrough of the LTC1063 is 50VRMS; for VS = 7.5V, the clock feedthrough approaches 75VRMS. Figure 8 shows a typical scope photo of the LTC1063 output pin when the input pin is grounded. The filter cutoff frequency was 1kHz, while scope bandwidth was chosen to be 1MHz such as switching transients above the 100kHz clock frequency will show. Wideband Noise The wideband noise of the filter is the RMS value of the device's output noise spectral density. The wideband noise data is used to determine the operating signal-to1063fa
LTC1063
APPLICATIO S I FOR ATIO
noise ratio at a given distortion level. The wideband noise (VRMS) is nearly independent of the value of the clock frequency and excludes the clock feedthrough. The LTC1063's typical wideband noise is 95VRMS. Figure 9 shows the same scope photo as Figure 8 but with a more sensitive vertical scale: The clock feedthrough is imbedded in the filter's wideband noise. The peak-to-peak wideband noise of the filter can be clearly seen; it is approximately 500VP-P. Note that 500VP-P equals the 95VRMS wideband noise of the part, multiplied by a crest factor or 5.25.
5mV/DIV
2s/DIV fCLK = 100kHz, fC = 1kHz, VS = 5V, 1MHz SCOPE BW
1063 F08
Figure 8. LTC1063 Output Clock Feedthrough + Noise
0.5mV/DIV
2s/DIV fCLK = 100kHz, fC = 1kHz, VS = 5V, 1MHz SCOPE BW
1063 F09
Figure 9. LTC1063 Output Clock Feedthrough + Noise
U
Aliasing Aliasing is an inherent phenomenon of sampled data filters and it primarily occurs when the frequency of an input signal approaches the sampling frequency. For the LTC1063, an input signal whose frequency is in the range of fCLK 6% will generate an alias signal into the filter's passband and stopband. Table 4 shows details. Example: LTC1063, fCLK = 20kHz, fC = 200kHz, fIN = (19.6kHz, 100mVRMS) fALIAS = (400Hz, 3.16mVRMS) An input RC can be used to attenuate incoming signals close to the filter clock frequency (Figure 10). A Butterworth passband response will be maintained if the value of the input resistor follows Table 1.
Table 4. Aliasing Data
OUTPUT AMPLITUDE REFERENCED TO INPUT SIGNAL 0 dB 0 dB - 3 dB - 10.2 dB - 17.7 dB - 24.3 dB - 30 dB - 40 dB - 48 dB - 54.5 dB - 60.4 dB - 65.5 dB - 70.16 dB - 78.25 dB - 85.3 dB - 100.3 dB
8 7 LTC1063 6 5 fCLK VOUT V+ 0.1F
W
UU
INPUT FREQUENCY 0.9995fCLK 0.995 fCLK 0.99 fCLK 0.9875fCLK 0.985 fCLK 0.9825fCLK 0.98 fCLK 0.975 fCLK 0.97 fCLK 0.965 fCLK 0.96 fCLK 0.955 fCLK 0.95 fCLK 0.94 fCLK 0.93 fCLK 0.9 fCLK
R VIN C V- 0.1F
OUTPUT FREQUENCY 0.0005 fCLK 0.005 fCLK 0.01 fCLK 0.0125 fCLK 0.015 fCLK 0.0175 fCLK 0.02 fCLK 0.025 fCLK 0.03 fCLK 0.035 fCLK 0.04 fCLK 0.045 fCLK 0.05 fCLK 0.06 fCLK 0.07 fCLK 0.1 fCLK
1 2 3 4
fCLK 1 f CLK 20 2RC 10
1063 F10
Figure 10. Adding an Input Anti-Aliasing RC
1063fa
11
LTC1063
APPLICATIO S I FOR ATIO
Group Delay
The group delay of the LTC1063 closely approximates the delay of an ideal 5-pole Butterworth lowpass filter (Figure 11, Curve A). To linearize the group delay of the LTC1063 (Figure 11, Curve B), use an input resistor about six times higher than the maximum value of RIN, shown in Table 1. The passband response of the group delay corrected filter approximates a 5-pole Bessel response while its transition band rolls off like a Butterworth.
(ms)
TYPICAL APPLICATIO S
Single 5V Supply Operation (fC = 3.4kHz)
5V 4.99k VIN 0.1F 4.53k 3 4 1 2 1F TANT 8 7 LTC1063 6 5 VOUT 5V 0.1F
+
13k
200pF
Cascading Two LTC1063s for Steeper Roll-Off
VIN* 1 2 3 -5V 0.1F R C 4 LTC1063 8 7 6 5 5V
0.1F
1 2 3 -5V 0.1F 4 LTC1063
8 7 6 5 0.1F VOUT 5V
fC (1/RC)(1/100) WIDEBAND NOISE = 140VRMS ATTENUATION AT f = 2fC = 60dB * IF THE INPUT VOLTAGE CAN EXCEED V +, CONNECT A SIGNAL DIODE BETWEEN PIN 1 AND V +.
1063 TA04
12
U
100 90 80 70 60 50 40 30 20 0 1 2 345678 INPUT FREQUENCY (kHz) 9 10 (B) GROUP DELAY CORRECTED (A) LTC1063 BUTTERWORTH
1063 F11
W
U
UU
Figure 11. Group Delay
Adjusting VOS(OUT) for 7.5 Supply Operation
10k
7.5V 10k
LT1009 VIN 1 2 V- -7.5V 1F TANT
1063 TA03
8 7 LTC1063 6 5 fCLK 0.1F 2.5mV VOUT V+ 7.5V *
1063 TA05
3
+
0.1F
4
* OPTIONAL, 1N4148
Sharing Clock for Multichannel Applications
VIN* 1 2 3 -5V 0.1F R C 4 LTC1063 8 7 6 5 0.1F VOUT 5V
VIN*
1 2 3 LTC1063
8 7 6 5 0.1F VOUT 5V
-5V 0.1F
4
* IF THE INPUT VOLTAGE CAN EXCEED V +, CONNECT A SIGNAL DIODE BETWEEN PIN 1 AND V +.
1063 TA06
1063fa
LTC1063
PACKAGE DESCRIPTIO
CORNER LEADS OPTION (4 PLCS)
.045 - .068 (1.143 - 1.650) FULL LEAD OPTION .300 BSC (7.62 BSC)
.008 - .018 (0.203 - 0.457)
NOTE: LEAD DIMENSIONS APPLY TO SOLDER DIP/PLATE OR TIN PLATE LEADS
U
J8 Package 8-Lead CERDIP (Narrow .300 Inch, Hermetic)
(Reference LTC DWG # 05-08-1110)
.005 (0.127) MIN .405 (10.287) MAX 8 7 6 5 .023 - .045 (0.584 - 1.143) HALF LEAD OPTION .025 (0.635) RAD TYP 1 2 3 .220 - .310 (5.588 - 7.874) 4 .200 (5.080) MAX .015 - .060 (0.381 - 1.524) 0 - 15 .045 - .065 (1.143 - 1.651) .014 - .026 (0.360 - 0.660) .100 (2.54) BSC .125 3.175 MIN
J8 0801
OBSOLETE PACKAGE
1063fa
13
LTC1063
PACKAGE DESCRIPTIO U
N8 Package 8-Lead PDIP (Narrow .300 Inch)
(Reference LTC DWG # 05-08-1510)
.400* (10.160) MAX 8 7 6 5 .255 .015* (6.477 0.381) 1 .300 - .325 (7.620 - 8.255) 2 3 4 .130 .005 (3.302 0.127) .045 - .065 (1.143 - 1.651) .065 (1.651) TYP .120 (3.048) .020 MIN (0.508) MIN .018 .003 (0.457 0.076)
N8 1002
.008 - .015 (0.203 - 0.381)
(
+.035 .325 -.015 8.255 +0.889 -0.381
)
.100 (2.54) BSC
INCHES MILLIMETERS *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .010 INCH (0.254mm)
NOTE: 1. DIMENSIONS ARE
1063fa
14
LTC1063
PACKAGE DESCRIPTIO U
SW Package 16-Lead Plastic Small Outline (Wide .300 Inch)
(Reference LTC DWG # 05-08-1620)
.050 BSC .045 .005 .398 - .413 (10.109 - 10.490) NOTE 4 16 15 14 13 12 11 10 9 N .420 MIN .325 .005 NOTE 3 .394 - .419 (10.007 - 10.643) N/2 N/2 1 .291 - .299 (7.391 - 7.595) NOTE 4 .010 - .029 x 45 (0.254 - 0.737)
0 - 8 TYP
.030 .005 TYP N
1
2
3
RECOMMENDED SOLDER PAD LAYOUT 2 3 4 5 6 7 8
.093 - .104 (2.362 - 2.642)
.037 - .045 (0.940 - 1.143)
.005 (0.127) RAD MIN
.009 - .013 (0.229 - 0.330)
NOTE 3 .016 - .050 (0.406 - 1.270)
.050 (1.270) BSC
.004 - .012 (0.102 - 0.305)
NOTE: 1. DIMENSIONS IN
.014 - .019 (0.356 - 0.482) TYP
S16 (WIDE) 0502
INCHES (MILLIMETERS) 2. DRAWING NOT TO SCALE 3. PIN 1 IDENT, NOTCH ON TOP AND CAVITIES ON THE BOTTOM OF PACKAGES ARE THE MANUFACTURING OPTIONS. THE PART MAY BE SUPPLIED WITH OR WITHOUT ANY OF THE OPTIONS 4. THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED .006" (0.15mm)
1063fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
15
LTC1063
TYPICAL APPLICATIO S
Low Noise DC Accurate Clock-Tunable Notch
R1 10k 0.1% 1 2 -5V 1F TANT 3 LTC1063 8 7 6 5 0.1F
VIN
+
0.1F
4
GAIN (dB)
* fNOTCH =
fCLK 119.04
* NOTCH DEPTH > 50dB (LTC1063)VOS * OUPUT DC OFFSET = 500V 2 * OUTPUT NOISE = 50VRMS fNOTCH 10.4 = * f(-20dB)BW 1
RELATED PARTS
PART NUMBER LTC1065 LTC1565-31 LTC1566-1 LT1567 LT1568 LTC1569-6 LTC1569-7 LT6600-2.5 LT6600-10 DESCRIPTION Clock-Tunable 5th Order Bessel Lowpass Filter 650kHz Linear Phase Lowpass Filter Low Noise, 2.3MHz Lowpass Filter Low Noise Op Amp and Inverter Building Block Low Noise, 10MHz 4th Order Building Block Linear Phase, DC Accurate, 10th Order Lowpass Linear Phase, DC Accurate, 10th Order Lowpass Low Noise Differential Amp and 10MHz Lowpass Low Noise Differential Amp and 20MHz Lowpass COMMENTS 1mV Offset, 80dB CMR Continuous Time, Fully Differential In/Out Continuous Time, Fully Differential In/Out Single Ended to Differential Conv Lowpass or Bandpass, Differential Outputs Resistor Set Clock, FC < 64kHz Resistor Set Clock, FC < 300kHz 55VRMS Noise 100kHz-10MHz 3V Supply 86VRMS Noise 100kHz-20MHz 3V Supply
16
Linear Technology Corporation
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 FAX: (408) 434-0507
U
-
R2 9.53k 0.1% V+ 5V fCLK LT1007
+
0 -10 -20 -30 -40 -50 -60 -70 215 fCLK = 100kHz fn = 840Hz 340 465 590 715 840 965 1090 INPUT FREQUENCY (Hz) 1215 1340 1465
1063 TA07
81Hz
1063fa LT/LT 0905 REV A * PRINTED IN USA
www.linear.com
(c) LINEAR TECHNOLOGY CORPORATION 1993

▲Up To Search▲

Price & Availability of LTC106309

	To Download LTC106309 Datasheet File
If you can't view the Datasheet, Please click here to try to view without PDF Reader .